VE TRACKSPORT BODY KIT & BONNETS

VE Commodore Aftermarket Body Kit & Bonnets

Description Freight USD Rural USD
Auckland
Auckland Region
$40.00
Whangarei / Hamilton
Up to Whangarei / Down to Hamilton
$0.00
North Island
Rest of North Island
$0.00
Christchurch
Christchurch Region
$0.00
South Island
Rest of South Island
$0.00
All of Australia
Australia Wide by NZ Post Economy Courier 3-4 working Days
$0.00
USA
USA Freight
$870.00

XAIR PERFORMANCE VE TRACKSPORT BODY KIT

Consists of Top quality Twin Nostril / Twin Exit Vent Bonnet or new ZL1 Camaro Style Bonnet, Front Bumper with Supercar Type Lip, Side Skirts, Rear Bumper Extensions & Lip Boot Spoiler for VE Commodore.

Create a distinctive tough look for your VE that's not a HSV Copy and no-one else has!

Painting and fitting can be arranged at the prices listed.

Note some cars with faded paint may need guards blended to match the bonnet colour at an extra cost.

VE TWIN NOSTRIL / TWIN EXIT VENT BONNET

Chunky side profile creates a super tough look on any VE!

Side Vents at the top of each side of the bonnet bulge create an exit point for the air coming in through the front nostrils allowing a constant cool air flow and reduced underbonnet temperatures for greater engine performance.

Unlike other cheap bonnets these have been developed from scratch to super tough standards for compliance in the Australian market. In Australia any aftermarket bonnet has to be certified as safe and registered against the cars serial number. 

The Bonnet comes pre-installed with Ball Joints and Latch ready to put straight on the car, after prep and paint the fit and finish is as good as the factory bonnet!

Mesh for Vents included.

Create a distinctive tough look for your VE no-one else has!

VE ZL1 CAMARO STYLE BONNET

Brand new VE Bonnet with Camaro ZL1 Centre Hump!

Top Vents funnel cool air into the engine bay for reduced underbonnet temperatures and greater engine performance.

Unlike other cheap bonnets these have been developed from scratch to super tough standards for compliance in the Australian market. In Australia any aftermarket bonnet has to be certified as safe and registered against the cars serial number. 

The Bonnet comes pre-installed with Ball Joints and Latch ready to put straight on the car, after prep and paint the fit and finish is as good as the factory bonnet!

Mesh for Vents included.

Create a modern look for your VE no-one else has!

VE FRONT BUMPER WITH SUPERCAR TYPE LIP

Top Quality Front Bumper developed from scratch specifically for VE Commodore Sedan, Wagon and Ute.

Two Models to fit both Series 1 and Series 2 with Headlight Shape Change.

Features Supercar Type Front Lip with same height all round which gives the illusion the car is a lot lower. Ideal for lowered cars as actual bumper height is only 10mm lower at centre front than the factory SS/SV6 Front Bumpers.

Fit and finish after prep and paint is as good as a factory bumper!

Mesh Kit and Single Spotlights are included.

Front Parking Sensors found in VE Calais can also be fitted to this Bumper.

VE SIDESKIRTS WITH VENT

Top quality Aftermarket Replacement Side Skirts for Holden VE Commodore Sedan & Wagon. Will not fit Ute. 

Factory Holden SS and SV6 Sideskirts feature a stepped in lip at the rear which make them look high. The Tracksport Sideskirts make the car look a lot lower due to no stepped in lip.

Vented Rear section comes complete with Mesh inserts.

Optional Tracksport Vinyl Graphics also available at prices as listed either shorter rear section only or full length with TRACKSPORT text as pictured. Custom Text also available no extra charge.

Fit and Finish after Prep, Primer and Painting is as good as Factory Sideskirts.

VE REAR BUMPER EXTENSIONS

If you've added the VE Tracksport Side Skirts then add the Rear Bumper Extensions to create a lower look all the way along the side of your car.

Construction material is Foam Rubber with self adhessive backing.

Will work with all SSV, SS, SV6, Omega, Berlina & Calais Rear Bumpers. 

Supplied in colour Flat Black once installed on the car the extensions can be painted with flexible primer before being painted the same colour as the car.

VE BOOT LIP SPOILER

Genuine Holden Low Profile Boot Lip Spoiler for all VE Sedans.

Construction : ABS Plastic

Create a Lower look for the rear of your VE!

Fits both VE Series 1 and Series 2.

Covers the rear holes in boot when standard SS, SV6 or SSV Spoilers are removed but front holes will need filling and top of boot re-painted.

 

POWER & CUSTOM BADGES

XAIR custom Domex Raised Resin Power Badges which are a similar Font / Style to VE HSV Badges.

Available in Chrome and Satin Black - most Numbers in stock. Price is for any 3 Numbered Badge.

TRACKSPORT and XAIR Performance Vehicles Domex Badges as pictured are also in stock. Any other Badges such as the CLUBSPORT 450mm wide door badges in Satin Black can be made to order.

VINYL WRAP

Vinyl Wrapping certain parts can dramatically change the look of your car without the hassle and expense of paint.

Contrast coloured Roofs and Spoilers etc make your car unique and different from standard.

Some of the higher spec VE's have chrome trims including door windows that stick out against certain paint colours. De-chroming of these parts including Badges with Vinyl Wrap makes for a much cleaner look.

d